Riverstone-networks WICT1-12 Manual do Utilizador Página 374
- Página / 718
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
17-66 Riverstone Networks RS Switch Router User Guide Release 8.0
Configuring L2 Tunnels MPLS Configuration
Note
The MTU size for MPLS ports must be at least 22 bytes more than the MTU size
of incoming non-MPLS traffic; additional bytes are required for multiple labels.
The default maximum transmission unit (MTU) size for non-MPLS ports on the
RS is 1522 bytes. The default MTU size for ports on MPLS-enabled line cards on
the RS is 1568 bytes, which allows for multiple MPLS labels).
The MPLS network must be configured with an MTU that is large enough to
transport the maximum size frame that will be transported in the tunnel LSP (this
can be at least 12 bytes more than the largest frame size). If an MPLS packet
exceeds the tunnel MTU, it will be dropped. If an egress LSR receives a packet
that exceeds the MTU of the destination L2 interface, the packet will be dropped.
FEC-Label Bindings
On the RS, the following can be used to identify the FEC-to-label binding for a virtual circuit:
•
VLAN ID assigned to a customer by a service provider
•
incoming port
•
incoming port and the customer-specific VLAN ID assigned by the customer
This section includes example configurations for each type of FEC-to-label binding.
Ingress and Egress LSR Configuration for L2 Dynamic Labels
On the ingress and egress LSRs, configure the following:
1.
Configure the L2 FEC.
-
If you are using the VLAN ID as the FEC, create the VLAN with the
vlan create
and
vlan
add ports
commands.
-
If you are using the incoming port as the FEC, use the
ldp map ports
command to map the
port to a logical customer ID number.
Note
The ports that are mapped to a single customer ID number must be either all trunk
ports or all access ports.
A port cannot be mapped to more than one customer ID number.
-
If you are using a combination of customer VLAN ID and incoming port as the FEC, create the
VLAN with the
vlan create
and
vlan add ports
commands and use the
ldp map ports
command to map the port to a logical customer ID number.
2.
Advertise the FEC-to-label mapping via LDP to the remote peers. Enable and start LDP.
-
Specify the remote LDP peer with the
ldp add remote-peer
command. Specify the router
ID of the remote LDP peer, which must be one of the loopback addresses of the remote router.
- RS Switch Router 1
- User Guide 1
- COPYRIGHT NOTICES 2
- RIVERSTONE NETWORKS, INC 8
- AGREEMENT 8
- TABLE OF CONTENTS 13
- LIST OF FIGURES 27
- LIST OF TABLES 31
- 1 INTRODUCTION 33
- 1.2 DOCUMENT CONVENTIONS 34
- 2 MAINTAINING CONFIGURATION 35
- 3 CLI AND RS BASICS 43
- 3.6 SETTING CLI PARAMETERS 49
- 3.7 NAMING RS PORTS 50
- 3.7.1 Port Type 51
- 3.7.2 Slot Number 51
- 3.7.3 Port Number 51
- 3.7.4 Channel Number 53
- 1000BASE-SXG8M-GSXB1-02 54
- CONTROL MODULES 57
- 4.2.2 Removing the Line Card 58
- Online Offline 60
- PC slot 1 60
- G8M-CM2-128 CONTROL MODULE 60
- PC slot 0 60
- (RS 8600 ONLY) 61
- Switching Fabric 62
- RS 38000 ONLY) 63
- 4.7 HOT SWAPPING A WIC 64
- ADDRESS-BASED) 65
- 5.3 VLAN OVERVIEW 66
- 5.3.1 RS VLAN Support 67
- 5.3.2 Configuration Examples 68
- AND 802.1Q SUPPORT) 69
- 70
- 5.6 CONFIGURING SPANNING TREE 71
- Setting the Bridge Priority 72
- Setting a Port Priority 73
- Assigning Port Costs 73
- Defining the Maximum Age 74
- 5.6.3 STP Dampening 75
- 5.7.2 Adding Ports to a VLAN 76
- 5.10 MONITORING BRIDGING 78
- 5.11 GARP/GVRP 79
- 5.11.3 Configuration Example 81
- Multiple Customer VLANs 84
- 6 SMARTTRUNK CONFIGURATION 101
- 6.1.1 Creating a SmartTRUNK 102
- Timesaver 103
- CONTROL PROTOCOL (LACP) 105
- 6.4.1 SLR Water-marks 109
- 6.4.2 Polling intervals 109
- Using Low Water-Mark Events 112
- Redistribution of IP Flows 112
- 7 CMTS CONFIGURATION GUIDE 113
- DOCSIS CMTSG8M-CMTSA-4X1 114
- US 1 US 2 US 3 US 4 IF DS 114
- 7.3.1 Headend Certification 115
- 7.3.2 IF-RF-Upconverter 115
- 7.3.3 Diplex Filters 115
- RS-8000 with 116
- DOCSIS CMTS 116
- DOWNSTREAM 117
- RECEIVER 119
- ! Configure the RS 124
- ! Configure the VLANs 124
- ! MOONLINK 124
- Client-VLAN Bindings 130
- 7.8 ANTI-SPOOFING 132
- 7.8.2 Anti-IP-spoofing 133
- Static Anti-IP Spoofing 134
- 8 ATM CONFIGURATION GUIDE 135
- 8.1 CONFIGURING ATM PORTS 136
- Cell Scrambling 137
- Cell Mapping 137
- VPI Bit Allocation 137
- 8.3 TRAFFIC SHAPING 140
- 8.4 TRAFFIC MANAGEMENT 142
- Relative Latency 143
- 8.5 BRIDGING ATM TRAFFIC 149
- 8.6 ROUTING ATM TRAFFIC 152
- 8.6.1 Peer Address Mapping 155
- ATM Cloud 156
- 8.7 CONFIGURING PPP (OC-12) 157
- DSL Modem 158
- 9 PACKET-OVER-SONET 161
- CONFIGURATION GUIDE 161
- SWITCHING 163
- 9.5 MONITORING POS PORTS 166
- 9.6 EXAMPLE CONFIGURATIONS 166
- 10 DHCP CONFIGURATION GUIDE 171
- 10.6 SECONDARY SUBNETS AND 176
- DIRECTLY-CONNECTED CLIENTS 176
- 11 IP ROUTING CONFIGURATION 179
- PARAMETERS 180
- 11.2.4 Unnumbered Interfaces 181
- 11.3 CONFIGURING JUMBO FRAMES 182
- at port et.3.1: 183
- 20:13a09f exit-port et.3.1 183
- RESOLUTION PROTOCOL (RARP) 184
- 11.5.3 Monitoring RARP 185
- 11.8 CONFIGURING IP HELPER 186
- 11.13 HARDWARE ROUTING TABLE 189
- 11.15 FORWARDING MODE 190
- Defining a Profile 191
- Applying a Profile 191
- Enabling a Port 191
- Access Control Lists (ACLs) 192
- Rate Limiting 192
- Quality of Service (QoS) 192
- L4 Bridging 192
- 11.18 CONFIGURATION EXAMPLES 196
- 12 VRRP CONFIGURATION GUIDE 197
- Configuration of Router R1 198
- Configuration for Router R2 199
- 10.0.0.1/16 201
- 10.0.0.2/16 201
- 10.0.0.3/16 201
- Configuration of Router R2 203
- Configuration of Router R3 204
- 12.2 ADDITIONAL CONFIGURATION 205
- 12.3 MONITORING VRRP 206
- 12.3.1 ip-redundancy trace 207
- 12.3.2 ip-redundancy show 207
- 12.4 VRRP CONFIGURATION NOTES 209
- 13 RIP CONFIGURATION GUIDE 211
- 13.3 MONITORING RIP 214
- 13.4 CONFIGURATION EXAMPLE 215
- 14 OSPF CONFIGURATION GUIDE 217
- 14.1 OSPF MULTIPATH 218
- 14.2 CONFIGURING OSPF 218
- 14.3 SETTING THE ROUTER ID 218
- 14.4 ENABLING OSPF 219
- 14.5 CONFIGURING OSPF AREAS 219
- 14.5.2 Configuring Stub Areas 220
- 14.8 CREATING VIRTUAL LINKS 224
- Setting Route Preference 227
- 14.10 MONITORING OSPF 228
- command: 229
- Figure 14-1 Exporting to OSPF 234
- 15 IS-IS CONFIGURATION GUIDE 235
- 15.3 ENABLING IS-IS ON THE RS 236
- 15.4.3 Setting the System ID 237
- Authentication Within an Area 238
- SNP Authentication 239
- Network Topology Overview 242
- IS-IS Area 1 243
- Area 49.da02 244
- IS-IS Area 2 244
- IS-IS Area 3 245
- IS-IS Area 4 246
- R1 Configuration 247
- R2 Configuration 248
- R3 Configuration 249
- R4 Configuration 250
- R5 Configuration 251
- R6 Configuration 252
- R7 Configuration 253
- R8 Configuration 253
- R9 Configuration 254
- C10 Configuration 255
- C10 Configuration (continued) 256
- R11 Configuration 257
- 16 BGP CONFIGURATION GUIDE 259
- 16.2 BASIC BGP TASKS 260
- 16.2.4 Adding a BGP Peer 262
- 16.2.5 Starting BGP 262
- BGP Confederation 265
- 16.2.10 Using Route Maps 267
- Enabling BGP Accounting 269
- IBGP Routing Group Example 275
- ; 279
- AS-64902 281
- AS-64901 281
- AS-64900 AS-64899 281
- Notes on Using Communities 286
- Physical Link 288
- Peering Relationship 288
- Information Flow 288
- Using the local-pref Option 289
- Using the set-pref Option 289
- 212.19.199.62/24 291
- 212.19.198.1/24 291
- 212.19.192.2/24 291
- 194.109.86.6 194.109.86.5 291
- 192.68.222.1 293
- 192.68.20.2 293
- 192.68.20.1 293
- 172.16.30.2 293
- 16.3.10 Route Map Example 300
- EBGP Accounting Example 301
- IBGP Accounting Example 303
- BGP DSCP Accounting 305
- 17 MPLS CONFIGURATION 309
- 17.1.1 Labels 310
- Label Distribution Protocols 314
- Label Advertising Mode 315
- Label Retention Mode 315
- Output Tag Table (OTT) 316
- Incoming Label Map (ILM) 317
- Context Address Memory (CAM) 317
- Table Lookups at Ingress LSRs 317
- Table Lookups at Transit LSRs 317
- Table Lookups at Egress LSRs 317
- 17.3 RSVP CONFIGURATION 321
- 17.3.2 RSVP Refresh Intervals 323
- 17.3.3 RSVP Hello Packets 324
- 17.3.4 Authentication 325
- 17.3.6 RSVP Refresh Reduction 326
- Message ID Extensions 327
- 17.4 LDP CONFIGURATION 329
- 17.4.3 Remote Peers 331
- 17.4.4 Loop Detection 331
- Ingress LSR Configuration 335
- Transit LSR Configuration 335
- PHP LSR Configuration 336
- # mpls show policy all 339
- Configuring an Explicit Path 340
- Configuring the LSP 341
- Adaptive LSP 343
- Bandwidth 343
- CoS Value 343
- Hop Limit 343
- LSP Metric 343
- Disabling CSPF 344
- Disabling TTL Decrementing 344
- Preference 344
- Connection Retries 344
- Policies 345
- ! Configure interfaces 359
- ! Configure OSPF 359
- DHCP Configuration 365
- 17.6 CONFIGURING L2 TUNNELS 368
- Egress LSR Configuration 370
- ! Create L2 static path TO-R1 372
- ! Start MPLS on this router 372
- Virtual Circuit Signaling 373
- Tunnel LSP Signaling 373
- FEC-Label Bindings 374
- ! If tunnel LSP uses RSVP: 379
- ! If tunnel LSP uses LDP: 379
- 17.7 TRAFFIC ENGINEERING 410
- ! Configure MPLS 419
- ! Enable and start RSVP 419
- ! Configure VLANs 419
- 17.7.3 IGP Shortcuts 427
- IS-IS IGP Shortcuts Example 428
- Advertising IGP Shortcuts 430
- 18.1 PREFERENCE 431
- Import-Source 432
- 18.1.2 Export Policies 433
- Export-Destination 434
- Export-Source 434
- Route-Filter 434
- Aggregate-Destination 436
- Aggregate-Source 436
- Authentication Methods 437
- protocol 448
- Figure 18-1 Exporting to RIP 449
- Figure 18-2 Exporting to OSPF 452
- 19 MULTICAST ROUTING 465
- CONFIGURATION 465
- 19.3 CONFIGURING IGMP 466
- 19.4 CONFIGURING DVMRP 468
- 19.6 CONFIGURATION EXAMPLE 471
- Setting the IP Policy Action 475
- Verifying Next-Hop Gateways 476
- 20.3 MONITORING IP POLICIES 483
- 21 NETWORK ADDRESS 487
- TRANSLATION CONFIGURATION 487
- 21.1.2 Setting NAT Rules 488
- 21.4 NAT AND DNS 489
- 21.5 NAT AND ICMP PACKETS 490
- 21.6 NAT AND FTP 490
- 21.7 MONITORING NAT 491
- 21.8 CONFIGURATION EXAMPLES 491
- Using Static NAT 492
- 21.8.2 Dynamic Configuration 493
- Using Dynamic NAT 494
- 21.8.4 Dynamic NAT with DNS 495
- Using Dynamic NAT with DNS 496
- 22 WEB HOSTING CONFIGURATION 499
- Specifying a Protocol 500
- 22.1.6 Setting Server Status 505
- 22.1.7 Load Balancing and FTP 506
- VSRP Example 507
- “OK” read-till-index 25 510
- Virtual IP Address Ranges 511
- Load Balancing with NAT 514
- 22.2 WEB CACHING 515
- Creating the Cache Group 516
- 22.2.2 Configuration Example 517
- Proxy Server Redundancy 518
- Verifying Servers 519
- 22.2.4 Monitoring Web-Caching 520
- 23 IPX ROUTING CONFIGURATION 521
- 23.5 CONFIGURING IPX ROUTING 525
- 23.7 CONFIGURATION EXAMPLES 528
- Adds a RIP access list 529
- Adds a SAP access list 529
- Adds a GNS access list 529
- 24 ACCESS CONTROL LIST 531
- 24.1.3 Implicit Deny Rule 534
- 24.2.1 Editing ACLs Offline 536
- 24.3 USING ACLS 538
- 24.3.4 Using ACLs as Profiles 540
- 24.4 ENABLING ACL LOGGING 544
- 24.5 MONITORING ACLS 545
- 25 SECURITY CONFIGURATION 547
- Monitoring RADIUS 548
- 25.1.2 Configuring TACACS 549
- 25.1.3 Configuring TACACS+ 549
- Monitoring TACACS+ 550
- 25.1.4 Configuring Passwords 551
- 25.1.5 Configuring SSH 551
- 25.2 LAYER-2 SECURITY FILTERS 552
- Example 1: Address Filters 556
- Static Entries Example 556
- Port-to-Address Lock Examples 557
- Example 2 : Secure Ports 557
- 25.4.6 Notes 561
- 26 QOS CONFIGURATION 563
- SPECIFICATION 564
- 26.3 RS QUEUING POLICIES 565
- LAYER-4 FLOWS 568
- Setting an IPX QoS Policy 569
- 26.8 TOS REWRITE 572
- 26.9 MONITORING QOS 574
- 26.10 LIMITING TRAFFIC RATE 575
- 26.10.1 Rate Limiting Modes 576
- 26.10.4 Port Rate Limiting 577
- Per-Flow Rate Limiting 580
- Flow-Aggregate Rate Limiting 580
- Aggregate Rate Limiting 581
- 27 PERFORMANCE MONITORING 583
- 28 RMON CONFIGURATION 587
- 28.1.2 RMON Groups 588
- Lite RMON Groups 589
- Standard RMON Groups 589
- 28.1.3 Control Tables 590
- 28.2 USING RMON 591
- 28.3 CONFIGURING RMON GROUPS 592
- <number> 593
- 28.4.1 RMON CLI Filters 596
- Creating RMON CLI Filters 597
- Using RMON CLI Filters 597
- 28.5 TROUBLESHOOTING RMON 598
- RS platform Maximum memory 600
- RS 32000 96 MB 600
- RS 8600 48 MB 600
- RS 8000 24 MB 600
- 29 LFAP CONFIGURATION GUIDE 601
- 30 WAN CONFIGURATION 605
- Static Addresses 606
- Mapped Addresses 607
- Dynamic Addresses 607
- Average Packet Size 608
- Nature of the Data 608
- 30.2.5 Packet Encryption 609
- 30.2.6 WAN Quality of Service 609
- Source Filtering and ACLs 610
- Weighted-Fair Queueing 610
- 30.3 FRAME RELAY OVERVIEW 611
- FOR THE RS 612
- 30.9 MONITORING PPP WAN PORTS 617
- 30.10 PPP PORT CONFIGURATION 618
- 30.13 WAN RATE SHAPING 621
- Rate Shaping by Best Effort 626
- Performing Rate Limiting 627
- Non-Rate Shaped Flows 627
- Router Connections on Subnet 630
- Router R1 Configuration File 631
- Router R2 Configuration File 631
- Router R3 Configuration File 632
- Router R4 Configuration File 632
- Router R5 Configuration File 633
- Router R6 Configuration File 633
- OVERVIEW 634
- TEST PORT 636
- T1, E1 AND T3 644
- Metropolitan Sevice Provider 645
- Hardware Requirements 648
- ISP RS 32000 Configuration 650
- RS 8600 Configuration (USA) 681
- T3 AND E3 687
- T3 refers to Channelized T3 688
- ISP RS 8000 Configuration 689
- 31 SERVICE CONFIGURATION 705
- 31.2 CREATING A SERVICE 707
- 31.3 APPLYING A SERVICE 710
- 31.4 SHOWING A SERVICE 712
- 31.4.2 Show All Command 713
- 31.5 PORT-LEVEL RATE LIMITING 714
- Customers 716
- Subnetwork 718
- 122.132.0.0/16 718
- 256 Kbps 718
Manuais e produtos relacionados com Hardware Riverstone-networks WICT1-12
(77 páginas)Transcend TS32MLS64V6D Handbücher
Bedienungsanleitungen und Benutzerhandbücher für Speichermodule Transcend TS32MLS64V6D.
Wir stellen 1 PDF-Handbücher Transcend TS32MLS64V6D zum kostenlosen herunterladen nach Dokumenttypen zur Verfügung Datenblatt
Comentários a estes Manuais