Riverstone Networks RS 8000 Manual do Operador Página 97
- Página / 158
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Riverstone Networks RS 8000/8600 Switch Router Getting Started Guide 3-11
Hardware Installation Installing the Hardware
Installing the PC Flash Card into the Control Module
The Control Module 16 megabyte PC flash card contains the system image software.
To install the PC flash card into the Control Module, perform the following steps:
1.
Make sure the power is off on the RS 8000/8600. You cannot install or remove a PC card while the
RS 8000/8600 is running.
2.
Insert the PC card into either of the slots on the Control Module. You can choose either slot.
Note
The RS 8000/8600 supports the use of dual PC cards, one in slot0, the other in
slot1. Each PC card is treated as an independent file system by the RS 8000/8600.
For detailed information regarding the PC flash file system and the management
of configuration files, see the “Riverstone RS Switch Router User Guide.”
Note
If the message “
SYS-E-NOFLASHCARD
” appears while booting the RS 8000/8600,
the system has not detected a PC card. If this occurs, ensure that the PC card is
properly inserted, then reboot. If the system still does not recognize the card,
contact Riverstone Networks, Inc. technical support.
Connecting to the Control Module’s Serial Port
To attach the supplied console cable to the Control Module DB-9 port:
1.
Locate the console cable included with the RS 8000/8600 chassis. The console cable is a
female-to-female DB-9 crossover cable. Thus, pin 2 (TXD or “transmit data”) emerges on the
terminal’s end of the connection as RXD (“receive data”), and so on.
2.
Plug one end of the console cable into the Control Module’s DCE DB-9 port.
3.
Plug the other end of the console cable into the terminal’s DTE port.
4.
When you are ready to begin configuring the RS, use procedures in Chapter 4, "Initial
Configuration" to power on the switch and boot the software. You will perform initial setup by
entering CLI commands on a terminal or PC running terminal emulation software.
Connecting to the Control Module’s 10/100Base-TX Port
Use the RJ-45 10/100Base-TX DTE port for management connections from a host on the network.
To attach a cable to the 10/100Base-TX port:
1.
Obtain a cable with an RJ-45 connector. Pin 1 (TXD or “transmit data”) must emerge on the
network’s end of the connection as RXD (“receive data”) and so on.
2.
After ensuring that the pin assignments on both ends of the connection are correct, plug the
appropriate end of the connection into the Control Module’s RJ-45 10/100Base-TX port.
3.
Connect the other end of the cable to your network.
- RS 8000/8600 1
- Switch Router 1
- Getting Started Guide 1
- COPYRIGHT NOTICES 2
- RADIACIÓN LÁSER Y CONECTORES 6
- RIVERSTONE NETWORKS, INC 9
- AGREEMENT 9
- RIVERSTONE STANDARD WARRANTY 11
- TABLE OF CONTENTS 15
- LIST OF FIGURES 19
- LIST OF TABLES 21
- 1 ABOUT THIS GUIDE 23
- 2 INTRODUCTION 25
- 2.2 SPECIFICATIONS 26
- Introduction Specifications 27
- 2.3 SOFTWARE OVERVIEW 28
- IP Routing 29
- IP Multicast Routing 29
- IPX Routing 29
- 2.3.9 Web Hosting Features 32
- 2.3.10 Management Platforms 32
- 2.4 HARDWARE OVERVIEW 33
- Switching Fabric 34
- Power supply 34
- 2.4.2 Backplane 35
- 2.4.3 Fan Module 35
- 2.4.4 Control Module 35
- Boot Flash 36
- Memory Module 36
- 100-125~5A 38
- 200-240~3A 38
- 50-60 Hz 38
- 100-125V~ 10A 39
- 200-240V~ 6A 39
- 50/60 Hz 39
- 2.4.6 DC Power Supply 40
- 10/100BASE-TXG8M-HTXA2-08 42
- 87654321 44
- 10/100BASE-TXG8M-HTXB2-16 45
- 100BASE-FXG8M-HFXA1-08 47
- 100Base-FX SFP Line Card 48
- 1000Base-SX Line Card 49
- 1000BASE-SXG8M-GSXB1-02 50
- 1000Base-LX Line Card 52
- 1000Base-LLX Line Card 54
- 1000Base-T Line Card 55
- Multi-Mode Short-Reach 58
- Single-Mode 58
- Long-Reach (70 Km) 58
- ATM Multi-Rate Line Card 63
- ATM OC-12c Line Card 64
- ATM-OC-12c-SMFG8M-A12B9-02 65
- POS OC-3 MMFG8M-PO3B1-04 66
- POS OC-3 SMFG8M-PO3B9-04 66
- POS OC-12c SMFG8M-P12B9-02 68
- G8M-PO3MM-02 69
- POS MPLS OC3 69
- G8M-P12MM-02 70
- POS MPLS OC-12c/STM-4 70
- Quad Serial - CEG8M-SECAC-04 71
- Dual HSSI 73
- G8M-HSIAC-02 73
- CMTS Line Card 75
- DOCSIS CMTSG8M-CMTSNA-6X1 76
- Multi-Rate WAN Line Card 77
- Channelized T3 Line Card 80
- CHANNELIZED T3G8M-CT3BB-02 81
- 18-695-01 82
- Figure 2-44 SRP bridge module 83
- 3 HARDWARE INSTALLATION 87
- 3.3 INSTALLING THE HARDWARE 88
- 3.2 HARDWARE SPECIFICATIONS 88
- Internal Power Supply One 94
- Internal Power Supply Two 94
- RS 8600 DC Power Supply 94
- Card Guides 96
- Circuit Board 96
- Metal Plate 96
- To remove 100
- Make sure WIC is aligned 104
- Insert the WIC through the 104
- (Base Slot) 105
- G8M-SRP-MATE 106
- Insert SFP into ports 107
- 4 INITIAL CONFIGURATION 109
- If the message “ 111
- 4.2.1 CLI Access Modes 112
- CONFIGURATION FILE 114
- 4.5 SETTING UP PASSWORDS 120
- Here is an example: 122
- 4.6 SETTING UP SNMP 123
- 4.6.2 Improving SNMP Security 124
- 4.6.3 Supported MIBs 125
- KRVWQD PH RU,3DGGU! 129
- IDFLOLW\W\SH! 129
- 4.9.1 Fail Over 131
- Software/Hardware Versions 134
- Changing Mastership 134
- Hot-Swapping 134
- 5 MANAGING SOFTWARE 135
- Reboot the RS 139
- Enter the 139
- 5.4 HITLESS SOFTWARE UPGRADE 143
- 5.4.1 Hitless Upgrade Example 144
- 5.5 UPGRADING FPGA CODE 146
- APPENDIX A TROUBLESHOOTING 149
- INFORMATION 151
- Numerics 153
Manuais e produtos relacionados com Redes Riverstone Networks RS 8000
Redes Riverstone Networks WICT1-12 Especificações
(111 páginas)
(111 páginas)
Redes Riverstone Networks RS 8000 Guia do Utilizador
(718 páginas)
(718 páginas)
Redes Riverstone Networks RS 2100 Especificações
(120 páginas)
(120 páginas)
Redes Riverstone Networks WICT1-12 Especificações
(77 páginas)
(77 páginas)
Transcend TS32MLR72V6D Handbücher
Bedienungsanleitungen und Benutzerhandbücher für Speichermodule Transcend TS32MLR72V6D.
Wir stellen 1 PDF-Handbücher Transcend TS32MLR72V6D zum kostenlosen herunterladen nach Dokumenttypen zur Verfügung Datenblatt
Comentários a estes Manuais